5b0e2db4fa
It was observed that in some cases, placing a breakpoint in an
assembler file using filename:line-number syntax would result in the
breakpoint being placed at a different line within the file.
For example, consider this x86-64 assembler:
test:
push %rbp /* Break here. */
mov %rsp, %rbp
nop /* Stops here. */
The user places the breakpoint using file:line notation targeting the
line marked 'Break here', GDB actually stops at the line marked 'Stops
here'.
The reason is that the label 'test' is identified as the likely start
of a function, and the call to symtab.c:skip_prologue_sal causes GDB
to skip forward over the instructions that GDB believes to be part of
the prologue.
I believe however, that when debugging assembler code, where the user
has instruction-by-instruction visibility, if they ask for a specific
line, GDB should (as far as possible) stop on that line, and not
perform any prologue skipping. I don't believe that the behaviour of
higher level languages should change, in these cases skipping the
prologue seems like the correct thing to do.
In order to implement this change I needed to extend our current
tracking of when the user has requested an explicit line number. We
already tracked this in some cases, but not in others (see the changes
in linespec.c). However, once I did this I started to see some
additional failures (in tests gdb.base/break-include.exp
gdb.base/ending-run.exp gdb.mi/mi-break.exp gdb.mi/mi-reverse.exp
gdb.mi/mi-simplerun.exp) where we currently expected a breakpoint
placed at one file and line number to be updated to reference a
different line number, this was fixed by removing some code in
symtab.c:skip_prologue_sal. My concern here is that removing this
check didn't cause anything else to fail.
I have a new test that covers my original case, this is written for
x86-64 as most folk have access to such a target, however, any
architecture that has a prologue scanner can be impacted by this
change.
gdb/ChangeLog:
* linespec.c (decode_digits_list_mode): Set explicit_line to a
bool value.
(decode_digits_ordinary): Set explicit_line field in sal.
* symtab.c (skip_prologue_sal): Don't skip prologue for a
symtab_and_line that was set on an explicit line number in
assembler code. Do always update the recorded symtab and line if
we do skip the prologue.
gdb/testsuite/ChangeLog:
* gdb.arch/amd64-break-on-asm-line.S: New file.
* gdb.arch/amd64-break-on-asm-line.exp: New file.
|
||
|---|---|---|
| bfd | ||
| binutils | ||
| config | ||
| contrib | ||
| cpu | ||
| elfcpp | ||
| etc | ||
| gas | ||
| gdb | ||
| gnulib | ||
| gold | ||
| gprof | ||
| include | ||
| intl | ||
| ld | ||
| libctf | ||
| libdecnumber | ||
| libiberty | ||
| opcodes | ||
| readline | ||
| sim | ||
| texinfo | ||
| zlib | ||
| .cvsignore | ||
| .gitattributes | ||
| .gitignore | ||
| ar-lib | ||
| ChangeLog | ||
| compile | ||
| config-ml.in | ||
| config.guess | ||
| config.rpath | ||
| config.sub | ||
| configure | ||
| configure.ac | ||
| COPYING | ||
| COPYING3 | ||
| COPYING3.LIB | ||
| COPYING.LIB | ||
| COPYING.LIBGLOSS | ||
| COPYING.NEWLIB | ||
| depcomp | ||
| djunpack.bat | ||
| install-sh | ||
| libtool.m4 | ||
| lt~obsolete.m4 | ||
| ltgcc.m4 | ||
| ltmain.sh | ||
| ltoptions.m4 | ||
| ltsugar.m4 | ||
| ltversion.m4 | ||
| MAINTAINERS | ||
| Makefile.def | ||
| Makefile.in | ||
| Makefile.tpl | ||
| makefile.vms | ||
| missing | ||
| mkdep | ||
| mkinstalldirs | ||
| move-if-change | ||
| multilib.am | ||
| README | ||
| README-maintainer-mode | ||
| setup.com | ||
| src-release.sh | ||
| symlink-tree | ||
| test-driver | ||
| ylwrap | ||
README for GNU development tools This directory contains various GNU compilers, assemblers, linkers, debuggers, etc., plus their support routines, definitions, and documentation. If you are receiving this as part of a GDB release, see the file gdb/README. If with a binutils release, see binutils/README; if with a libg++ release, see libg++/README, etc. That'll give you info about this package -- supported targets, how to use it, how to report bugs, etc. It is now possible to automatically configure and build a variety of tools with one command. To build all of the tools contained herein, run the ``configure'' script here, e.g.: ./configure make To install them (by default in /usr/local/bin, /usr/local/lib, etc), then do: make install (If the configure script can't determine your type of computer, give it the name as an argument, for instance ``./configure sun4''. You can use the script ``config.sub'' to test whether a name is recognized; if it is, config.sub translates it to a triplet specifying CPU, vendor, and OS.) If you have more than one compiler on your system, it is often best to explicitly set CC in the environment before running configure, and to also set CC when running make. For example (assuming sh/bash/ksh): CC=gcc ./configure make A similar example using csh: setenv CC gcc ./configure make Much of the code and documentation enclosed is copyright by the Free Software Foundation, Inc. See the file COPYING or COPYING.LIB in the various directories, for a description of the GNU General Public License terms under which you can copy the files. REPORTING BUGS: Again, see gdb/README, binutils/README, etc., for info on where and how to report problems.